GB/T 25876-2010 牛早期胚胎性别的鉴定 巢式PCR法
作者:标准资料网 时间:2024-05-19 16:05:23 浏览:8348
来源:标准资料网
基本信息
| 标准名称： | 牛早期胚胎性别的鉴定 巢式PCR法 |
| 英文名称： | Method of nested PCR for sex identification of early cattle embryo |
| 中标分类： |
农业、林业 >>
畜牧 >>
家畜、家禽 |
| ICS分类： |
农业 >>
农业和林业 >>
动物饲养和繁殖
|
| 发布部门： | 中华人民共和国国家质量监督检验检疫总局 中国国家标准化管理委员会 |
| 发布日期： | 2011-01-10 |
| 实施日期： | 2011-06-01 |
| 首发日期： | 2011-01-10 |
| 作废日期： | |
| 主管部门： | 全国畜牧业标准化技术委员会 |
| 提出单位： | 中华人民共和国农业部 |
| 归口单位： | 全国畜牧业标准化技术委员会 |
| 起草单位： | 华中农业大学 |
| 起草人： | 张淑君、杨利国、李翔、刘辉、刘文举、胡修忠 |
| 出版社： | 中国标准出版社 |
| 出版日期： | 2011-06-01 |
| 页数： | 8页 |
| 书号： | 155066·1-41599 |
适用范围
本标准规定了牛早期胚胎性别鉴定的巢式PCR方法。
本标准适用于奶牛和肉牛胚胎或胎儿的性别鉴定。
前言
没有内容
目录
没有内容
引用标准
下列文件中的条款通过本标准的引用而成为本标准的条款。凡是注日期的引用文件,其随后所有的修改单(不包括勘误的内容)或修订版均不适用于本标准,然而,鼓励根据本标准达成协议的各方研究是否可使用这些文件的最新版本。凡是不注日期的引用文件,其最新版本适用于本标准。
GB/T6682 分析实验室用水规格和试验方法
所属分类： 农业 林业 畜牧 家畜 家禽 农业 农业和林业 动物饲养和繁殖
【英文标准名称】:Costinformation;calculationprinciples;typesandmethodsofcalculation
【原文标准名称】:成本信息.计算原理.成本核算的方式方法
【标准号】:DIN32992-1-1989
【标准状态】:作废
【国别】:德国
【发布日期】:1989-12
【实施或试行日期】:
【发布单位】:德国标准化学会(DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:信息;数学计算;成本;成本会计;成本情报;数量估计
【英文主题词】:information;costs;costaccounting;costinformations;mathematicalcalculations;quantitysurveying
【摘要】:
【中国标准分类号】:A02
【国际标准分类号】:03_100_60
【页数】:7P;A4
【正文语种】:德语
Product Code:SAE J356
Title:Welded Flash-Controlled Low-Carbon Steel Tubing Normalized for Bending, Double Flaring, and Beading *HS-150/2000*
Issuing Committee:Metallic Tubing Committee
Scope:The SAE Standard covers normalized electric-resistance welded flash-controlled single-wall, low-carbon steel pressure tubing intended for use as pressure lines and in other applications requiring tubing of a quality suitable for bending, double flaring, beading, forming, and brazing. Material produced to this specification is not intended to be used for single flare applications due to the potential leak path that would be caused by the ID weld bead.This specification also covers SAE J356 Type-A tubing. The mechanical properties and performance requirements of standard SAE J356 and SAE J356 Type-A are the same. Therefore, the designated differences of Type-A tubing are not meant to imply that Type-A tubing is in anyway inferior to standard SAE J356. The Type-A designation is only meant to address the unique manufacturing differences of the small diameter, light wall sizes (typically 15.88 mm OD x 1.24 mm wall and smaller.) The primary differences between SAE J356 and SAE J356 Type-A are described in the following paragraph.Type-A tubing is heat treated in-line to relieve stresses and is generally produced in coiled form. When Type-A tubing is produced in coil form, straight lengths of Type-A are only available through a secondary straightening and cut-to-length operation. Standard SAE J356 is produced as straight lengths and then receives a secondary normalizing operation. All standard SAE J356 requirements apply to Type-A tubing unless the specific requirement is noted with a 脪Type-A脫 designation. Standard SAE J356 is also available in the same sizes as Type-A, in which case all the standard SAE J356 specifications apply.
